ES - Artigos em revistas internacionais
Permanent URI for this collection
Browse
Browsing ES - Artigos em revistas internacionais by Author "Alves, L. C."
Now showing 1 - 6 of 6
Results Per Page
Sort Options
- Assessment of dye distribution in sensitized solar cells by microprobe techniquesPublication . Barreiros, M. Alexandra; Corregidor, V.; Alves, L. C.; Guimarães, Fernanda; Mascarenhas, João; Torres, Erica; Brites, Maria JoãoDye sensitized solar cells (DSCs) have received considerable attention once this technology offers economic and environmental advantages over conventional photovoltaic (PV) devices. The PV performance of a DSC relies on the characteristics of its photoanode, which typically consists of a nanocrystalline porous TiO2 film, enabled with a large adsorptive surface area. Dye molecules that capture photons from light during device operation are attached to the film nanoparticles. The effective loading of the dye in the TiO2 electrode is of paramount relevance for controlling and optimizing solar cell parameters. Relatively few methods are known today for quantitative evaluation of the total dye adsorbed on the film. In this context, microprobe techniques come out as suitable tools to evaluate the dye surface distribution and depth profile in sensitized films. Electron Probe Microanalysis (EPMA) and Ion Beam Analytical (IBA) techniques using a micro-ion beam were used to quantify and to study the distribution of the Ru organometallic dye in TiO2 films, making use of the different penetration depth and beam sizes of each technique. Different 1D nanostructured TiO2 films were prepared, morphologically characterized by SEM, sensitized and analyzed by the referred techniques. Dye load evaluation in different TiO2 films by three different techniques (PIXE, RBS and EPMA/WDS) provided similar results of Ru/Ti mass fraction ratio. Moreover, it was possible to assess dye surface distribution and its depth profile, by means of Ru signal, and to visualize the dye distribution in sample cross-section through X-ray mapping by EPMA/EDS. PIXE maps of Ru and Ti indicated an homogeneous surface distribution. The assessment of Ru depth profile by RBS showed that some films have homogeneous Ru depth distribution while others present different Ru concentration in the top layer (2 lm thickness). These results are consistent with the EPMA/EDS maps obtained.
- CdTe nano-structures for photovoltaic devicesPublication . Corregidor, V.; Alves, L. C.; Franco, N.; Barreiros, M. Alexandra; Sochinskii, N. V.; Alves, E.CdTe nano-structures with diameter of ∼100 nm and variable length (200–600 nm) were fabricated on glass substrates covered with conductive buffer layers such as NiCr, ZAO (ZnO:Al2O3 + Ta2O5) or TiPd alloys. The fabrication process consisted of the starting vapour deposition of metal catalyst dropped layer followed by the isothermal catalyst-prompted vapour growth of CdTe nano-structured layer of controllable shape and surface filling. The effect of buffer layers on the crystallographic orientation and thickness of CdTe nano-structured layers is investigated by means of IBA techniques, SEM and X-ray diffraction. It was shown that the formed CdTe nano-layers have a cubic structure, mainly oriented towards the [1 1 1] crystallographic direction, except for those grown on ZAO layer where the X-ray diffraction signal is very weak to be associated to any crystallographic form. The RBS spectra recorded on different areas of each sample type showed an almost constant thickness and SEM images revealed an homogeneous and dense distribution of the structures. It was also possible to study the first stage of the nano-structures grown on the Bi2Te3 seeds.
- Microscopy techniques for dye distribution in DSCs nanocrystalline TiO2 filmsPublication . Barreiros, M. Alexandra; Sequeira, S.; Alves, L. C.; Corregidor, V.; Guimarães, Fernanda; Mascarenhas, João; Brites, Maria JoãoCapture of sunlight has attracted an increasing interest in the scientific community and triggered the development of efficient and cheap photovoltaic devices. Amongst recent generation technologies for solar energy conversion, dye-sensitized solar cells (DSCs) show an optimal trade-off between high-conversion efficiency and low-cost manufacturing. For the last two decades, significant progress has been made and best energy conversion efficiency of the DSC at the laboratory scale has surpassed 12% [1]. A lot of work has focused on the enlargement of surface areas to enhance the amount of adsorbed dyes by reduction of nanoparticle sizes or utilization of novel structures. Nevertheless there remain some crucial details of DSC operation for which limited information is available, namely dye diffusion and adsorption, surface coverage and dye distribution throughout the nc-TiO2 film. Microprobe techniques can be powerful tools to evaluate the dye load, the dye distribution and dye depth profile in sensitized films. Electron Probe Microanalysis (EPMA) and Ion Beam Analytical (IBA) techniques using a micro-ion beam, namely micro-Particle Induced X-ray Emission ( PIXE) and Rutherford Backscattering Spectrometry (RBS), were used to quantify and to study the distribution of the ruthenium organometallic (N719) dye in TiO2 films, profiting from the different penetration depth and beam sizes of each technique. Two different types of films were prepared and sensitized, mesoporous nanoparticles and 1D nanostructured TiO2 films (figure 1). Despite the low concentration of Ru, the high sensitive analytical techniques used allowed to assess the Ru surface distribution and depth profile. Fig. 2 shows the PIXE maps of Ru and Ti indicating an homogeneous surface distribution. The same figure presents the RBS spectra obtained with a 2 MeV proton beam of the same sample showing that a good spectra fit is obtained considering only two sample layers: the first one with a 1.7 ìm thickness; the second one being the SiO2 substrate. The Ru RBS signal also shows that the dye has an homogeneous depth distribution. Due to the fine spatial resolution of the EPMA/WDS (Wavelength Dispersive Spectroscopy) technique it was possible to visualise the dye distribution in sample cross-section (with micrometer or submicrometer dimensions) as presented in Fig. 3 for the elemental mapping of a mesoporous nanoparticle TiO2 film. Dye load evaluation by two different techniques (ìPIXE and EPMA/WDS) provided similar results (Ru/Ti values around 0.5 %). The distribution analysis of the organometallic dye (N719) was done through ruthenium distribution via X-ray mapping. RBS was used to assess the ruthenium depth profile. This assessment can lead to a better understanding of the device performance.
- On the influence of silica type on the structural integrity of dense La9.33Si2Ge4O26 electrolytes for SOFCsPublication . Alves, Cátia; Marcelo, Teresa; Oliveira, Fernando Almeida Costa; Alves, L. C.; Mascarenhas, João; Trindade, B.Apatite-type rare earth based oxides, such as R-doped lanthanum oxides of general formula La9.33(RO4)6O2 with R = Ge, Si, exhibit high ionic conductivity and low activation energy at moderate temperatures, when compared to the yttria-stabilized zirconia electrolyte making them potential materials to be used in the range 500–700 °C, for intermediate temperature solid oxide fuel cells (IT-SOFCs). In this study, dense oxyapatite-based La9.33Si2Ge4O26 electrolytes have been successfully prepared either by electrical sintering at 1400 °C or microwave hybrid sintering at 1350 °C for 1 h from La2O3, SiO2 and GeO2 powders dry milled at 350 rpm for 15 h in a planetary ball mill. The densification behaviour of the apatite-type phase synthesized by mechanical alloying was found to be dependent on the grade of SiO2 used: either pre-milled quartz powder or amorphous nanosized fumed silica. The influence of the silica type on the La9.33Si2Ge4O26 integrity was assessed by dynamic Young's modulus, microhardness and indentation fracture toughness measurements. A good correlation between the degree of densification (as observed by SEM/EDS) and the resulting mechanical properties could be established. Pre-milling of quartz powder has favoured higher densification rates to be attained suggesting that both Fe content, resulting from the dry milling (as determined by PIXE analyses) and crystallinity of SiO2 do promote densification of these electrolytes thereby improving their structural integrity.
- The earrings of Pancas treasure: Analytical study by X-ray based techniques – A first approachPublication . Tissot, Isabel; Tissot, M.; Manso, M.; Alves, L. C.; Barreiros, M. Alexandra; Marcelo, Teresa; Carvalho, M. L.; Corregidor, V.; Guerra, M. F.The development of new metallurgical technologies in the Iberian Peninsula during the Iron Age is well represented by the 10 gold earrings from the treasure of Pancas. This work presents a first approach to the analytical study of these earrings and contributes to the construction of a typological evolution of the Iberian earrings. The manufacture techniques and the alloys composition were studied with three complementary X-ray spectroscopy techniques: portable EDXRF, μ-PIXE and SEM–EDS. The results were compared with earrings from the same and previous periods.
- Ultrafast low-temperature crystallization of solar cell graded formamidinium-cesium mixed-cation lead mixed-halide perovskites using a reproducible microwave-based processPublication . Brites, Maria João; Barreiros, M. Alexandra; Corregidor, V.; Alves, L. C.; Pinto, Joana V.; Mendes, Manuel Joao; Fortunato, Elvira; Martins, Rodrigo; Mascarenhas, JoãoABSTRACT: The control of morphology and crystallinity of solution-processed perovskite thin-films for solar cells is the key for further enhancement of the devices’ power conversion efficiency and stability. Improving crystallinity and increasing grain size of perovskite films is a proven way to boost the devices’ performance and operational robustness, nevertheless this has only been achieved with high-temperature processes. Here, we present an unprecedented low-temperature (<80 °C) and ultrafast microwave (MW) annealing process to yield uniform, compact, and crystalline FA0.83Cs0.17Pb(I(1–x)Brx)3 perovskite films with full coverage and micrometer-scale grains. We demonstrate that the nominal composition FA0.83Cs0.17PbI1.8Br1.2 perovskite films annealed at 100 W MW power present the same band gap, similar morphology, and crystallinity of conventionally annealed films, with the advantage of being produced at a lower temperature (below 80 °C vs 185 °C) and during a very short period of time (∼2.5 min versus 60 min). These results open new avenues to fabricate band gap tunable perovskite films at low temperatures, which is of utmost importance for Mechanically flexible perovskite cells and monolithic perovskite based tandem cells applications.