Browsing by Author "Mardolcar, U. V."
Now showing 1 - 5 of 5
Results Per Page
Sort Options
- New WC-Cu composites for the divertor in fusion reactorsPublication . Dias, Marta; Pinhão, N.; Faustino, R.; Martins, Ricardo; Ramos, A. S.; Vieira, M. T.; Correia, J.B.; Camacho, E.; Fernandes, F. M. Braz; Nunes, B.; Almeida, Amélia; Mardolcar, U. V.; Alves, E.ABSTRACT: The requirements for the divertor components of future fusion reactors are challenging and therefore a stimulus for the development of new materials. In this paper, WC-Cu composites are studied for use as thermal barrier between the plasma facing tungsten tiles and the copper-based heat sink of the divertor. Composite materials with 50% vol. WC were prepared by hot pressing and characterized in terms of microstructure, density, expansion coefficient, elastic modulus, Young's modulus and thermal diffusivity. The produced materials consisted of WC particles homogeneously dispersed in a Cu matrix with densifications between 88% and 98%. The sample with WC particles coated with Cu evidenced the highest densification. The thermal diffusivity was significantly lower than that of pure copper or tungsten. The sample with higher densification exhibits a low value of Young's modulus (however, it is higher compared to pure copper), and an average linear thermal expansion coefficient of 13.6 x 10(-6) degrees C-1 in a temperature range between 100 degrees C and 550 degrees C. To estimate the behaviour of this composite in actual conditions, a monoblock of the divertor in extreme conditions was modelled. The results predict that while the use of WC-Cu interlayer leads to an increase of 190 degrees C on the temperature of the upper part of the monoblock when compared to a pure Cu interlayer, the composite will improve and reduce significantly the cold-state stress between this interlayer and the tungsten.
- The effects of mechanical alloying on the physical and thermal properties of CuCrFeTiV alloyPublication . Antão, Francisco; Dias, Marta; Correia, J.B.; Galatanu, Andrei; Galatanu, M.; Mardolcar, U. V.; Myakush, A.; Cruz, M. M.; Casaca, António; Silva, R.C. da; Alves, E.ABSTRACT: The present work reports the production and key properties of the CuCrFeTiV high entropy alloy synthetized mechanical alloying and spark plasma sintering. The milled powders and the as-sintered samples were analysed through scanning electron microscopy, coupled with energy dispersive X-ray spectroscopy and particle induced X-ray emission. Magnetic properties together with electrical resistivity, thermal conductivity, specific heat differential thermal analysis were also evaluated on the consolidated samples. The powders reveal an increasing content in iron as the millings are prolonged up to 20 h. The elemental composition of the sintered alloy, determined through particle induced X-ray emission, confirms the final composition after mechanical alloying with an increase of iron and a decrease in the remaining elements. Furthermore, although the alloy presents electrical resistivity typical of a high entropy alloy, a ferromagnetic behaviour was found, consistently with major Fe content as detected in prior observations. Finally, thermal measurements show that this CuCrFeTiV entropy alloy possesses thermal properties suitable for its potential use as thermal barriers.
- The effects of tantalum addition on the microtexture and mechanical behaviour of tungsten for ITER applicationsPublication . Tejado, Elena; Carvalho, Patricia Almeida; Munoz, A.; Dias, Marta; Correia, J.B.; Mardolcar, U. V.; Pastor, Jose YgnacioTungsten (W) and its alloys are very promising materials for producing plasma-facing components (PFCs) in the fusion power reactors of the near future, even as a structural part in them. However, whereas the properties of pure tungsten are suitable for a PFC, its structural applications are still limited due to its low toughness, ductile to brittle transition temperature and recrystallization behaviour. Therefore, many efforts have been made to improve its performance by alloying tungsten with other elements. Hence, in this investigation, the thermo-mechanical performance of two new tungsten-tantalum materials has been evaluated. Materials with W–5wt.%Ta and W–15wt.%Ta were processed by mechanical alloying (MA) and later consolidation by hot isostatic pressing (HIP), with distinct settings for each composition. Thus, it was possible to determine the relationship between the microstructure and the addition of Ta with the macroscopic mechanical properties. These were measured by means of hardness, flexural strength and fracture toughness, in the temperature range of 300–1473 K. The microstructure and the fracture surfaces features of the tested materials were analysed by Field Emission Scanning Electron Microscopy (FESEM).
- Tungsten–nanodiamond composite powders produced by ball millingPublication . Nunes, D.; Livramento, Vanessa; Mardolcar, U. V.; Correia, J.B.; Carvalho, Patricia AlmeidaThe major challenge in producing tungsten–nanodiamond composites by ball milling lies in successfully dispersing carbon nanoparticles in the metallic matrix while keeping carbide formation at a minimum. Processing windows for carbide minimization have been established through systematic variation of the nanodiamond fraction, milling energy and milling time. Materials characterization has been carried out by X-ray diffraction, scanning and transmission electron microscopy and microhardness testing. Nanostructured matrices with homogeneously dispersed particles that preserved the diamond structure have been produced. Differential thermal analysis has been used to evaluate the composites thermal stability.
- WC-Cu thermal barriers for fusion applicationsPublication . Dias, Marta; Guerreiro, F.; Tejado, Elena; Correia, J.B.; Mardolcar, U. V.; Coelho, M.; Palacios, T.; Pastor, Jose Ygnacio; Carvalho, Patricia Almeida; Alves, E.ABSTRACT: WC-Cu cermets have been devised for thermal barriers between the plasma facing tungsten tiles and the copperbased heat sink in the first wall of nuclear fusion reactors. Composite materials with 50 and 75 v/v% WC have been prepared by hot pressing at 1333 and 1423 K with pressures of 37 and 47 MPa, respectively. Microstructural changes have been investigated by scanning electron microscopy coupled with energy dispersive X-ray spectroscopy and X-ray diffraction. The materials consolidated have also been evaluated in terms of Archimedes' density, thermal diffusivity, Vickers hardness and elastic modulus. Implantation was carried out at room temperature with Ar+ at 100 keV ion beam with a fluence of 4 · 1020 at/m2. The materials consisted of homogeneous dispersions of WC particles in a Cu matrix and presented densifications of about 90%. Incipient swelling in copper-rich regions have been observed on the implanted surfaces, however no significant changes have been detected by X-ray diffraction. Higher WC content in the cermet materials increased hardness and the elastic modulus. The cermets' thermal diffusivity was significantly lower than that of pure copper or tungsten, as desirable for a thermal barrier.