Materiais para a Energia - ME
URI permanente desta comunidade:
Navegar
Percorrer Materiais para a Energia - ME por Objetivos de Desenvolvimento Sustentável (ODS) "13:Ação Climática"
A mostrar 1 - 6 de 6
Resultados por página
Opções de ordenação
- Enhancing Proton Conductivity of SPEEK Based Membranes by Incorporation Graphene Oxide / Bisphosphonic acid dopant [Resumo]Publication . Teixeira, Fatima; Teixeira, António Paulo Silva; Rangel, Carmen M.ABSTRACT: The most commercially successful membrane for applications in fuel cell and electrolyzers, perfluorinated sulfonic NafionR, exhibits relevant performance limitations due to its dependence on water content with consequent proton mobility restrictions, environmental concerns and very high cost. Poly(etheretherketone) (SPEEK) polymer appears as a versatile non-fluorinated alternative for a low-cost and a more environmentally friendly membrane. Our previous studies showed that the incorporation of biphosphonic acid dopants (BPs) into the mentioned polymeric matrices, improves membrane proton conduction and durability1-5. In this work, we prepared and evaluated new doped SPEEK membranes using graphene oxide (GO) with bisphosphonic acid functionalities as dopant (GOBP), anticipating superior membranes properties, including proton conductivity.
- Functional alginate aerogels as green catalytic platform for CO₂-to-syngas conversion [Resumo]Publication . Messias, Sofia; Paninho, A. B.; Vieira, G.; Souza, A.; Rangel, Carmen M.; Nunes, Daniela; Martins, Rodrigo; Mendes, Manuel Joao; Machado, Ana
- Li-ion Battery Recycling: A Summary ReviewPublication . Nogueira, Carlos; Neiva Correia, Maria Joana; Margarido, Fernanda; Plancha, Maria João; Pedrosa, Fátima; Gonçalves, Ana; Silva, Clara; Silva, SaraABSTRACT: A short review of battery recycling technologies is presented. Main components and materials of battery cells, modules and packs are identified, highlighting their compositions and contents. Main component of packs is aluminium, followed by the cathode materials, anode materials, copper and polymers. Safe discharge of the spent batteries is mandatory, and the subsequent dismantling allows separation and valorisation of the aluminium casings, electronic components, polymers and steel. The resulting cells or modules are pretreated by shearing and drying, and the solvent and evolving gases shall be safely treated and disposed. Physical separation operations, including secondary shredding, sieving, gravity separation, among others, are applied to separate the Al, Cu and polymer fragments from the electrode powders (black mass). Metallurgical processing, by hydro or pyrometallurgy, allows further recovery of the metals in pure forms, which are then sent back to the market. Nowadays, several hydrometallurgical processes are being introduced, allowing high recovery yields of the most important metals such as lithium, cobalt, nickel and manganese. By this way, a more sustainable management of the resources can be achieved.
- Lithium Role in the Clean Energy Transition: Challenges and Prospects [Comunicação oral]Publication . Almeida, Joana; Pedrosa, Fátima; Plancha, Maria João; Gonçalves, Ana; Nogueira, Carlos
- Tetrahedrite Nanocomposites for High Performance ThermoelectricsPublication . Coelho, Rodrigo; Moço, Duarte; Sá, Ana; Luz, Paulo P. da; Neves, Filipe; Cerqueira, Maria de Fátima; Lopes, E.B.; Brito, Francisco; Mangelis, Panagiotis; Kyratsi, Theodora; Pereira Gonçalves, AntonioABSTRACT: Thermoelectric (TE) materials offer a promising solution to reduce green gas emissions, decrease energy consumption, and improve energy management due to their ability to directly convert heat into electricity and vice versa. Despite their potential, integrating new TE materials into bulk TE devices remains a challenge. To change this paradigm, the preparation of highly efficient tetrahedrite nanocomposites is proposed. Tetrahedrites were first prepared by solid state reaction, followed by the addition of MoS2 nanoparticles (NPs) and hot-pressing at 848 K with 56 MPa for a duration of 90 min to obtain nanocomposites. The materials were characterized by XRD, SEM-EDS, and Raman spectroscopy to evaluate the composites' matrix and NP distribution. To complement the results, lattice thermal conductivity and the weighted mobility were evaluated. The NPs' addition to the tetrahedrites resulted in an increase of 36% of the maximum figure of merit (zT) comparatively with the base material. This increase is explained by the reduction of the material's lattice thermal conductivity while maintaining its mobility. Such results highlight the potential of nanocomposites to contribute to the development of a new generation of TE devices based on more affordable and efficient materials.
- Thermal Stability and Irradiation Resistance of (CrFeTiTa)70W30 and VFeTiTaW High Entropy AlloysPublication . Pereira, André; Martins, Ricardo; Monteiro, Bernardo; Correia, Jose B.; Galatanu, Andrei; Catarino, Norberto; Jenus, Petra; Dias, MartaABSTRACT: Nuclear fusion is a promising energy source. The International Thermonuclear Experimental Reactor aims to study the feasibility of tokamak-type reactors and test technologies and materials for commercial use. One major challenge is developing materials for the reactor's divertor, which supports high thermal flux. Tungsten was chosen as the plasma-facing material, while a CuCrZr alloy will be used in the cooling pipes. However, the gradient between the working temperatures of these materials requires the use of a thermal barrier interlayer between them. To this end, refractory high-entropy (CrFeTiTa)70W30 and VFeTiTaW alloys were prepared by mechanical alloying and sintering, and their thermal and irradiation resistance was evaluated. Both alloys showed phase growth after annealing at 1100 degrees C for 8 days, being more pronounced for higher temperatures (1300 degrees C and 1500 degrees C). The VFeTiTaW alloy presented greater phase growth, suggesting lower microstructural stability, however, no new phases were formed. Both (as-sintered) alloys were irradiated with Ar+ (150 keV) with a fluence of 2.4 x 1020 at/m2, as well as He+ (10 keV) and D+ (5 keV) both with a fluence of 5 x 1021 at/m2. The morphology of the surface of both samples was analyzed before and after irradiation showing no severe morphologic changes, indicating high irradiation resistance. Additionally, the VFeTiTaW alloy presented a lower deuterium retention (8.58%) when compared to (CrFeTiTa)70W30 alloy (14.41%).