GEOCIÊNCIAS
Permanent URI for this community
Browse
Browsing GEOCIÊNCIAS by Subject "3D geological modelling"
Now showing 1 - 3 of 3
Results Per Page
Sort Options
- 3D Constrained Gravity Inversion and TEM, Seismic Reflection and Drill-Hole Analysis for New Target Generation in the Neves-Corvo VMS Mine Region, Iberian Pyrite BeltPublication . Marques, Fábio; Dias, Pedro; Carvalho, João; Represas, Patricia; Spicer, Bill; Araújo, Vítor; Matos, João Xavier; Morais, Igor; Albardeiro, Luís; Sousa, Pedro; Pacheco, Nelson; Gonçalves, Pedro; Barbosa, DiegoABSTRACT: Located in the Iberian pyrite belt, the Neves-Corvo mine is a world-class massive sulfide deposit and the largest operating mine in Portugal with underground mining down to 1000 m depth focused on massive and stockwork Cu, Zn, Pb rich ores. Gravimetric data have had a leading role in the discovery of the seven known deposits, together with time-domain electromagnetic (TEM) ground data. In this work, we present the results of a 3D constrained gravity inversion carried out with legacy ground gravity data. The 3D gravity inversions were carried out using an updated density database containing approximately 142,000 measurements. A recently constructed 3D geological model based on reprocessed 2D seismic reflection, 3D seismic, TEM and updated geology from detailed surface mapping and drill-hole data, was used to constrain the inversions. The results show multiple high-density anomalies that may indicate the presence of mineralization at depth. These anomalies were therefore cross-checked with holes previously drilled. Approximately 97% of more than 1000 available surface drill-holes located on or at a distance of less than 200 m from the high-density anomalies intersected mineralization. However, gravity anomalies have been drilled in the past and particularly dense black shales or rhyolitic/gabbroic rocks have been intersected. To increase the success of future drilling, gravimetric anomalies have been correlated spatially with high-conductivity TEM zones and strong-amplitude seismic reflections, because igneous rocks usually present weak-to-moderate conductivity and a massive column of black shales presents a seismic signature quite different from that of mineralization. We concluded that some of these locations represent high-quality targets to consider following up with drilling and further exploration.
- 3D reflection seismic imaging of volcanogenic massive sulphides at Neves-Corvo, PortugalPublication . Donoso, George; MALEHMIR, Alireza; Carvalho, João; Araújo, VítorABSTRACT: Three-dimensional reflection seismic data from the Neves-Corvo area, southern Portugal, were reprocessed with the main objective of improving the seismic signature of the Lombador and Semblana volcanogenic massive sulphide deposits. The sensitivity for choosing adequate parameters for targeted imaging, even during the pre-processing stage, such as common-depth point binning size, was studied in detail before the main processing work began helping to optimize bin size parameters; preliminary stacking results from this analysis presented severe acquisition footprint, and seismic targets were not clearly identifiable. Processing results using pre-stack dip move-out and post-stack migration methods show strong moderate to steeply dipping reflections. Several of the observed reflections can be correlated with known lithological contacts, some of which are interpreted to originate from the Semblana and Lombador deposits. Despite the mixed signal-to-noise ratio, the seismic cube reveals both shallow and deep three-dimensional structures, allowing to account for the deposits' lateral extension beyond the capabilities of two-dimensional seismic imaging alone. Given the data processing approach taken it was possible to distinguish strong diffraction patterns, interpreted as originating from faults and edges of the Lombador deposit, illustrating the usefulness of diffraction patterns for better interpretation of geological features in hard-rock environments.
- A drill‑hole, geological and geophysical data‑based 3D model for target generation in Neves‑Corvo mine region, PortugalPublication . Carvalho, João; Dias, Pedro; Revaux, Charles; Matos, João Xavier; Araújo, Vítor; Inverno, Carlos; Marques, Fábio; Donoso, George; Pacheco, Nelson; Morais, Igor; Albardeiro, Luis; Batista, Maria Joao; MALEHMIR, Alireza; Spicer, Bill; de Oliveira, Daniel Pipa SoaresABSTRACT: The Neves-Corvo world class Iberian Pyrite Belt volcanogenic massive sulphide (VMS) deposit located in southern Portugal, constitutes an important Cu–Zn–Pb active mine. Seven deposits are currently known, among which the Lombador deposit alone has estimated 150 Mt of massive sulphides. The life-time of the mine is dependent on the discovery of new exploration targets and it is vital to have accurate 3D geological models, not only to guide drilling campaigns but also to drive a winning/ new strategy, which in the past has led to Semblana and Monte Branco discoveries: geophysical inversion and modelling. Furthermore, 3D geological models can contribute to the understanding of the tectonic and stratigraphic evolution of the region. Therefore, the goal of this study is to produce a realistic 3D geological model of the Neves-Corvo region, as only one model is presently publicly available: the PROMINE model, which includes the study area of this work and extends from Aljustrel to the border with Spain. Lundin Mining has also produced two unpublished, confdential models in 2007 and 2017. The latest Lundin model incorporates the same geophysical data used in this work (2D and 3D seismic refection and time-domain electromagnetic (TEM) ground loop data) and approximately 7500 surface and underground drill-holes. The model presented in this research has much more detail than the 2012 PROMINE model in the Neves-Corvo region and uses an updated and revised drill-hole database with approximately 8000 drill-holes, revised geological cross-sections built from surface geology and drill-hole logs, new geological outcrop data, petrophysical and reprocessed geophysical data, and is therefore more detailed and accurate than any of the previous models, in particular the 2007 and PROMINE models. Land gravimetric and aeromagnetic data are also available in the study area but were not directly used to build the geological model but rather to investigate and check the model produced. Modelling was performed with industry standard software and the 3D curves resulting from the geological/geophysical interpretation were interpolated using diferent approaches to respect the hard data (interpretation lines and drill-holes). The resulting 3D stratigraphic surfaces required strong manual editing to respect the interpretation, due to the presence of folds, thrusts and tectonic nappes in the study area. The surfaces were afterwards tied to the drill-holes, resulting in a 3D model with great accuracy and detail in the near mining area and covering a larger area than previously available 3D geological models. The model has three major stratigraphic layers: the Mértola Flysch Formation and the Volcano-Sedimentary Complex (VSC), overlying the Phyllite-Quartzite Formation basement, and also the known VMS deposits (underlying the top of the Lower VSC) geometries according to drill-hole data. In the central part of the study area, where more drill-holes are available, the top of the Lower VSC sequence surface was also built. This approach will contribute to a better exploration drill-hole planning and the generation of new targets for exploration.