ME - Artigos em revistas internacionais
URI permanente para esta coleção:
Navegar
Percorrer ME - Artigos em revistas internacionais por Domínios Científicos e Tecnológicos (FOS) "Engenharia e Tecnologia::Outras Engenharias e Tecnologias"
A mostrar 1 - 9 de 9
Resultados por página
Opções de ordenação
- Detection of corrosion on silvered glass reflectors via image processingPublication . Wiesinger, Florian; Baghouil, Sarah; Le Baron, Estelle; Collignon, Romain; Santos, Filipa; Cunha Diamantino, Teresa; Catarino, Isabel; Facão, Jorge; Ferreira, Cristina; Páscoa, Soraia; Sutter, Florian; Fernández-García, Aránzazu; Wette, JohannesABSTRACT: A novel characterization technique based on image analysis is presented, intended to complement state-of-the-art reflectometer measurements. The technique is developed by experts from different laboratories (OPAC, AGC, CEA and LNEG), which subsequently conduct two Round Robin experiments on corroded solar reflectors for validation. Regarding the inter-comparability, it is found that parameters like the corrosion spot density or the penetration maximum on coated edges exhibit an average coefficient of variation of 62.6 % and 54.9 %. Better agreement is found for parameters like the total corroded area and the maximum edge corrosion penetration, with coefficients of variation of 14.3 % and 13.4 %, respectively. The developed methodology is further applied during a 68-month lasting outdoor exposure campaign of two types of solar reflectors at two representative sites, one exhibiting corrosivity class C2 and the other C3. On the commercial coating RL1, a total corroded area of 59 mm2 and 426 mm2 is measured after the outdoor exposure on the C2 and the C3 site, respectively, while on the novel low-lead coated reflector RL3 corresponding values are 280 mm2 and 1308 mm2. This shows the superior quality of the coating RL1 in terms of corrosion resistance. Furthermore, the analysis highlights the importance of proper edge sealing for corrosion protection, since corrosion penetration is increased by a factor between 1.3 and 4.0 if the edges are unprotected. The reflectance decrease after the outdoor exposure is regarded as negligible (0.000 - 0.005), thus not permitting any of the conclusions that are made from the novel image analysis technique.
- Determination of reflectance of interest from limited state-of-the-art solar reflector field soiling measurementsPublication . Wette, Johannes; Sutter, Florian; Cunha Diamantino, Teresa; Montecchi, Marco; Bern, Gregor; Fernández-García, AránzazuABSTRACT: In concentrated solar thermal technologies, plant operators usually monitor the soiling of their solar field with handheld reflectometers. These measurements can be used for yield calculations and to adapt cleaning strategies: if the reflectometer reading falls below an empirically established threshold, the solar field should be cleaned. There are several commercial reflectometers available for this purpose, but all of them measure at different combinations of wavelength, acceptance angle or incidence angle. It is the purpose of this study to bring the readings from all main commercial reflectometers to the same representative value, enabling their comparison with one another and the translation of these readings into a meaningful reflectance parameter. Thus, different handheld reflectometers are correlated with a laboratory reflectometer, capable of measuring in the whole solar spectral region, covering a wide range of incidence and acceptance angles. The most significant parameter is the near-specular solar-weighted reflectance, measured at the typical incidence and acceptance angles for a given plant, as it is the most precise parameter to describe the reflected energy from the solar field. The correlations for all included reflectometers, show highly linear correlations over a wide range of soiling levels with low deviations. Consequently, the correlations presented herein enable the plant operators at the studied site to compute the near-specular solar-weighted reflectance from their reflectometer readings. and, with that, increase the significance of the measurements without collecting any additional data. The work also establishes a detailed procedure to derive this type of correlations at any site of interest.
- Evolution of atomically dispersed co-catalysts during solar or UV photocatalysis for efficient and sustained H2 productionPublication . Capelo, Anabela; Fattoruso, Domenico; Valencia-Valero, Laura; Esteves, M. Alexandra; Rangel, Carmen M.; Puga, AlbertoABSTRACT: The evolution of metal/titania photocatalysts during photocatalytic H-2 evolution is herein studied. Samples containing atomically dispersed Pt co-catalysts (single atoms, clusters and sub-nanoparticles) formed after calcination were compared to pre-reduced analogues mostly having metallic nanoparticles (diameters >1 nm) during ethanol photoreforming under either UV-rich irradiation or natural sunlight. Aggregation of ultra-dispersed oxidised platinum entities (Pt delta+) with concomitant reduction into Pt-0 nanoparticles (1-2 nm) was observed after UV irradiation by transmission electron microscopy (TEM), and diffuse reflectance UV-visible (DRUV-vis) and X-ray photoelectron (XPS) spectroscopies. A parallel, albeit slower, evolution trend was evidenced during solar photocatalysis. Conversely, atomically dispersed Cu co-catalyst species did not grow and became in-situ reduced into sub-nanometric Cu-0 under irradiation. Hydrogen production rates were remarkably high during initial stages of UV irradiation, and then declined to a sustained regime (approximate to 50 and 8 mmol g(-1) h(-1) for Pt/TiO2 or Cu/TiO2, respectively, for up to 24 h of irradiation). Steadier solar photoreforming was observed in experiments performed in a compound parabolic collector tubular reactor (approximate to 7.6 and 1.7 mmol g(-1) h(-1) for Pt/TiO2 or Cu/TiO2, respectively). Despite the non-negligible effect of co-catalyst rearrangement on activity rationalised herein, attenuated total reflectance Fourier-transform infrared (ATR-FTIR) spectroscopy measurements pre- and post-photocatalysis suggest that accumulation of strongly adsorbed degradation intermediates, chiefly acetate, is a major cause for rate decreases. Notwithstanding, this phenomenon did not result in total deactivation, so that sustained hydrogen production upon long-term irradiation was not compromised.
- Exploring Marine Biomineralization on the Al-Mg Alloy as a Natural Process for In Situ LDH Growth to Improve Corrosion ResistancePublication . Marques, Maria João; Mercier, Dimitri; Seyeux, Antoine; Zanna, Sandrine; Tenailleau, Christophe; Duployer, Benjamin; Jeannin, Marc; Marcus, Philippe; Basséguy; BASSEGUY, RegineABSTRACT: This study provides a detailed characterization of the AA5083 aluminum alloy, surface, and interface over 6 months of immersion in seawater, employing techniques such as SEM/EDX, GIXRD, mu-Raman and XPS. The purpose was to evaluate the evolution of the biomineralization process that occurs on the Al-Mg alloy. By investigating the specific conditions that favor the in situ growth of layered double hydroxide (LDH) during seawater immersion as a result of biomineralization, this research provides insights into marine biomineralization, highlighting its potential as an innovative and sustainable strategy for corrosion protection.
- Mechanical Performance of Ceria-Coated 3D-Printed Black Zirconia Cellular Structures After Solar Thermochemical CO/H2 Fuel Production CyclesPublication . Oliveira, Fernando; Sardinha, Manuel; Justino Netto, Joaquim Manoel; Leite, Marco; Farinha, Miguel; Barreiros, Maria Alexandra; Abanades, Stéphane; Fernandes, JorgeABSTRACT: Solar fuels production requires developing redox active materials with porous structures able to withstand thermochemical cycles with enhanced thermal stability under concentrated solar irradiation conditions. The mechanical performance of 3D-printed, macroporous black zirconia gyroid structures, coated with redox-active ceria, was assessed for their suitability in solar thermochemical cycles for CO2 and H2O splitting. Experiments were conducted using a 1.5 kW solar furnace to supply the high-temperature concentrated heat to a windowed reaction chamber to carry out thermal redox cycling under realistic on-sun conditions. The ceria coating on ceramic structures improved the thermal stability and redox efficiency while minimizing the quantity of the redox material involved. Crushing strength measurements showed that samples not directly exposed to the concentrated solar flux retained their mechanical performance after thermal cycling (similar to 10 MPa), while those near the concentrated solar beam focus exhibited significant degradation due to thermal stresses and the formation of CexZr1-xO2 solid solutions (similar to 1.5 MPa). A Weibull modulus of 8.5 was estimated, marking the first report of such a parameter for fused filament fabrication (FFF)-manufactured black zirconia with gyroid architecture. Failure occurred via a damage accumulation mechanism at both micro- and macro-scales. These findings support the viability of ceria-coated cellular ceramics for scalable solar fuel production and highlight the need for optimized reactor designs.
- Novel fast synthesis route for α-MgAgSb thermoelectric materialsPublication . Santos, Beatriz; Sá, Ana; Luz, Paulo P. da; Neves, Filipe; de Boor, Johannes; Pereira Gonçalves, AntonioABSTRACT: Thermoelectric (TE) materials capable of waste heat recovery in the temperature range of 300-525 K remain relatively underdeveloped compared to conventional Bi2Te3-based systems, which present inherent environmental, health, and cost challenges. Recently, MgAgSb-based compounds have garnered significant research interest for applications in this temperature range owing to their intrinsically low thermal conductivity, high figure of merit and higher abundance. However, synthesis of the desired low-temperature alpha-MgAgSb phase typically requires highly controlled production processes-such as multi-step mechanical alloying, followed by extensive, week-long annealing-to mitigate the formation of or transition to undesirable phases. This study proposes an original, rapid, and scalable synthesis strategy combining induction melting for only six minutes with the subsequent classic hot-pressing method. We investigated the effect of nominal stoichiometry on thermoelectric performance by synthesising three distinct compositions: MgAg0.97Sb0.995, MgAg0.965Sb0.985, and MgAg0.955Sb0.985. The MgAg0.955Sb0.985 composition exhibited optimal performance, achieving an average power factor (PF) of 12.8 mu W K-2 cm-1 in the 300-525 K range. By considerably reducing the thermal budget and processing time, this approach significantly improves the energy payback time (EPBT) and reduces the carbon footprint of production, addressing the critical sustainability-performance trade-off that limits large-scale deployment. This result validates the capacity of the proposed fast synthesis route to yield performant MgAgSb-based samples and suggests that the optimal nominal composition is dependent on the specific production technique employed. Fundamentally, this work demonstrates the rapid and successful preparation of the desired alpha-MgAgSb phase using an easily scalable technique that does not require a perpetually inert atmosphere. This process utilises bulky precursor elements directly, significantly reducing production complexity, associated costs, and health hazards. This advancement provides a simpler and more industrially viable pathway for the transition of MgAgSb materials toward commercial availability.
- Scale-up of a clean hydrogen production system through the hydrolysis of sodium borohydride for off-grid applicationsPublication . Silva, Diogo; Nunes, Helder Xavier; Rangel, Carmen M.; Pinto, A. M. F. R.ABSTRACT: Hydrogen is considered a promising energy vector with the potential to replace fossil fuels, and sodium borohydride serves as an effective energy carrier capable of releasing hydrogen (H2) for off-grid applications. However, the hydrolysis of sodium borohydride has only matured at laboratory-scale. Therefore, the scale-up of a laboratory reactor was designed and manufactured to study the effect of larger H2 production. For that, the effect of inhibitor NaOH concentration and water quality were studied. Experiments using 3 wt% NaOH showed overall better performance than those using 1 wt%. Additionally, experiments using tap water - scarcely reported in the literature - demonstrated performance equal to or better than that achieved with distilled water. These results are indicative of a possible significant reduction in the H2 production cost through this method.
- Thermally modified wood: assessing the impact of weathering on mechanical strength and exposure to subterranean termitesPublication . Godinho, Delfina; Lourenco, Ana; Araújo, Solange; Machado, José Saporiti; Nunes, Lina; Duarte, Marta; Duarte, Sónia; Ferreira, Cristina; Quilhó, Teresa; Cunha Diamantino, Teresa; Gominho, JorgeABSTRACT: The main objective of this study was to evaluate the mechanical properties of three thermal-modified wood species when exposed to weathering in urban and maritime/industrial environments and their durability against subterranean termites. The wood species studied were Maritime pine, ash, and blackwood acacia. All wood samples were exposed to two different environments (urban and maritime/industrial) for 24 months. Then, its physical and mechanical properties were evaluated (modulus of elasticity (MOE), modulus of rupture (MOR), compression strength (CS), and modulus of compression (MOC). Thermally modified woods revealed a lower density, which could explain the loss of MOE and MOR. In compression, no significant changes were verified. The weathered samples showed changes in mechanical properties, mostly verified in MOE and MOR, where some decreases were reported in both locations. Tests were performed to evaluate biodegradation and the resistance of all wood samples to subterranean termites. The grade of attack (approximate to 4) and termite survival rate were similar in all wood species (above 75% and lower than 80%), except for modified acacia (59%), which could indicate that thermal modification increased toxic substances. The cellulose degradation was reflected in FTIR-ATR and Py-GC/MS in natural and thermally modified woods. Py-GC/MS showed a decrease in levoglucosan, while lignin suffered some modifications with slight changes in monomeric composition reflected by the reduction of the S/G ratio. No changes were found between the two environments, and thermal modification did not give extra protection against termites and weathering.
- Thermochemical performance of ceria coated-macroporous 3D-printed black zirconia structures for solar CO/H2 fuels productionPublication . Oliveira, Fernando; Barreiros, Maria Alexandra; Sardinha, Manuel; Leite, Marco; Fernandes, Jorge; Abanades, StéphaneABSTRACT: The use of macroporous structured ceria for the solar thermochemical splitting of CO2 and H2O to produce clean fuels through two-step redox cycles was investigated. The research aimed to assess the reactivity of 3D-printed black zirconia gyroid structures coated with a microporous layer of pure CeO2 for producing CO and H2. Such porous designs are intended to increase both the absorption of solar radiation and the available surface area for the solid-gas reaction. It was observed that the structure degraded more at the top of the reactor cavity, where the formation of CexZr1-xO2 solid solutions occurred at the coating/substrate interface. Besides, the porous ceria structure remained after redox cycles in the samples not directly exposed to solar radiation. Consequently, the solar reactor achieved CO and H2 production rates of up to 5.4 and 1.9 mL min-1 g-1 with fuel yield over 0.2 mmol g-1, and the material maintained its performance over several consecutive cycles without any loss of reactivity. This indicates a strong potential for producing solar fuels at a large facility using custom 3D-printed ceria-coated structures.