Publication
Towards stable bifunctional oxygen electrodes and corrosion resistant gas diffusion layers for regenerative fuel cells
| dc.contributor.author | Silva, R. A. | |
| dc.contributor.author | Soares, C. O. | |
| dc.contributor.author | Carvalho, M. D. | |
| dc.contributor.author | Jorge, M. E. Melo | |
| dc.contributor.author | Gomes, A. | |
| dc.contributor.author | Pereira, M. I. da Silva | |
| dc.contributor.author | Rangel, C. M. | |
| dc.date.accessioned | 2013-09-23T10:56:41Z | |
| dc.date.available | 2013-09-23T10:56:41Z | |
| dc.date.issued | 2013 | |
| dc.description.abstract | ABSTRACT: Regenerative fuel cells (RFCs) can provide very high energy storage at minimal weight in a dual mode system, by combining an electrolyzer and a fuel cell. Although RFCs are an appealing technology their development is still at an early stage. One key issue is the search for highly active electrocatalysts for both oxygen reduction and water oxidation. Presently, platinum is the best electrocatalyst for the oxygen reduction reaction (ORR), but has a poor oxygen evolution (OER) performance while metal oxides catalyze the OER but not the ORR. Yet, the search for the development of bi-functional oxygen electrodes is also associated to structurally stable gas diffusion layers - they must be capable of withstanding high potentials when cells are operated in the electrolyzer mode and in addition, mass transport limitations when used as a cathode in fuel cell mode. A novel approach is used in this work to tackle the issue, focussing on the development of stable gas diffusion electrodes for the oxygen reactions, having as a base high surface area LaNiO3. Previous work by the authors has optimised the synthesis of the mentioned perovskite-type oxide, prepared by a self-combustion method. The high electrochemical surface area and low porosity of the oxide has been indicated by electrochemical impedance spectroscopy (EIS) and BET measurements. A full characterization has been the subject of recent publications [1,2]. In a first instance, carbon diffusion electrodes on carbon paper are considered. The gas diffusion layers were prepared from carbon black Vulcan XC-72 R, with a LaNiO3 loading of 3 mg cm-2. To fabricate the catalyst layer, an ink was prepared by suspending LaNiO3 in isopropanol, and stirring in an ultrasonic bath to thoroughly wet and disperses it. A 5% Nafion® dispersion solution (Electrochem, Inc) was then added to the mixture. The catalyst inks were dispersed onto the gas diffusion layer with a brush, and dried at 50°C, until the desired catalys t loading was achieved. Finally, a Nafion layer was painted and dried at 50ºC. Significant current densities were obtained in both OER and ORR domains. A full electrochemical study was conducted in order to obtain the kinetic parameters in the OER region using a 1 M KOH solution. Cyclability and stability tests were also conducted. The tests were done in two potential ranges and served as a means of electrode conditioning. The electrode was also subjected to 200 cycles between 0.25 and 0.55 V vs Ag/AgCl (sat.) and an extra 100 cycles between -0.40 and 0.6 V vs Ag/AgCl (sat.), at a scan rate of 100 mV s-1. Additionally a constant current density of ~10 mA cm-2 was applied during 50 hours with simultaneous potential monitoring. Activity loss and increasing resistance of the electrodes were observed using cyclic voltammetry and EIS respectively. Carbon oxidation is favorable at the working potentials used which might sets a practical limit on the lifetime of the GDE. In a second instance, the deposition of LaNiO3 on a Ni foam (1.6 mm thickness, 95% porosity) was effected bringing about more stability in the OER region and Tafel slopes (47 mVdec-1) practically half of the value encountered in the case of carbon paper electrodes. Stability under galvanostatic conditions was assessed at current densities 10 times larger than those used in the case of the carbon paper (100 mA cm-2), also during 50 h, with excellent results. Due to the high stability at anodic potentials found with the Ni foam electrodes and in order to increase current densities, composite electrodes LaNiO3/Pt-Ru were prepared as an alternative to carbon paper electrodes. Results obtained using non-supported Pt-Ru (5-30 wt%) are discussed and compared with the case of carbon-supported Pt-Ru nanoparticles, in the same experimental conditions. It is suggested that LaNiO3 can be used as susbstitute material for carbon black, avoiding the effects of carbon corrosion in the OER region. | por |
| dc.identifier.citation | Silva, R.A.; Soares, C.O.; Carvalho, M.D.; Jorge, M.E. Melo; Gomes, A.; Pereira, M.I. da Silva; Rangel, C.M. Towards stable bifunctional oxygen electrodes and corrosion resistant gas diffusion layers for regenerative fuel cells. In: HYCELTEC'2013 - IV Iberian Symposium on Hydrogen, Fuel Cells and Advanced Batteries, Book of Abstracts, Estoril, 26-28 June, 2013 | por |
| dc.identifier.uri | http://hdl.handle.net/10400.9/1998 | |
| dc.language.iso | eng | por |
| dc.subject | Perovskite-type oxides | por |
| dc.subject | Oxygen reactions | por |
| dc.subject | Gas diffusion electrodes | por |
| dc.subject | Regenerative fuel cells | por |
| dc.subject | Platinum | por |
| dc.title | Towards stable bifunctional oxygen electrodes and corrosion resistant gas diffusion layers for regenerative fuel cells | por |
| dc.type | conference object | |
| dspace.entity.type | Publication | |
| oaire.citation.conferencePlace | Estoril, Portugal | por |
| oaire.citation.title | HYCELTEC'2013 - IV Iberian Symposium on Hydrogen, Fuel Cells and Advanced Batteries | por |
| person.familyName | Rangel | |
| person.givenName | Carmen M. | |
| person.identifier.ciencia-id | AA13-FF7C-9E29 | |
| person.identifier.orcid | 0000-0001-7996-8142 | |
| person.identifier.rid | D-5477-2011 | |
| person.identifier.scopus-author-id | 7006108156 | |
| rcaap.rights | openAccess | por |
| rcaap.type | conferenceObject | por |
| relation.isAuthorOfPublication | 804e595a-d539-46a2-ae78-6cadc8ca9457 | |
| relation.isAuthorOfPublication.latestForDiscovery | 804e595a-d539-46a2-ae78-6cadc8ca9457 |