ENERGIA
Permanent URI for this community
Browse
Browsing ENERGIA by Field of Science and Technology (FOS) "Engenharia e Tecnologia::Engenharia dos Materiais"
Now showing 1 - 10 of 13
Results Per Page
Sort Options
- Comparison of the corrosion of ferritic and austenitic stainless steel (AISI 430 and AISI 316L) with LiNaK carbonate salts for thermal energy storage in CSP/CST applicationsPublication . Gil, Mafalda; Pedrosa, Fátima; Paiva Luís, Teresa; Figueira Vasques, Isabel; Oliveira, Fernando; Cunha Diamantino, TeresaABSTRACT: This study focuses on the corrosion rates and mechanisms of two stainless steels, austenitic AISI 316L and ferritic AISI 430, in contact with a eutectic mixture of LiNaK carbonates in long-term tests at 650 degrees C. The selection of these two stainless steels was based on their differences, both in their intrinsic characteristics and in the cost associated with each one. The research also underscores the importance of optimizing the descaling methods used to evaluate the corrosion rate. Corrosion rates were measured gravimetrically according to ISO 17245:2015, revealing an asymptotic behavior for both steels, with AISI 430 with a corrosion rate of 237 f 21 mu m and AISI 316L of 151 f 13 mu m after 2000 h of testing. Corrosion mechanisms were analyzed using SEM/EDS, GDOES, and XRD techniques, which identified well-defined oxide layers with varying compositions. Given the observed corrosion mechanisms and its lower cost, AISI 430 steel seems to have great applicability in CSP/CST plants, provided it is paired with an appropriate protective coating.
- Detection of corrosion on silvered glass reflectors via image processingPublication . Wiesinger, Florian; Baghouil, Sarah; Le Baron, Estelle; Collignon, Romain; Santos, Filipa; Cunha Diamantino, Teresa; Catarino, Isabel; Facão, Jorge; Ferreira, Cristina; Páscoa, Soraia; Sutter, Florian; Fernández-García, Aránzazu; Wette, JohannesABSTRACT: A novel characterization technique based on image analysis is presented, intended to complement state-of-the-art reflectometer measurements. The technique is developed by experts from different laboratories (OPAC, AGC, CEA and LNEG), which subsequently conduct two Round Robin experiments on corroded solar reflectors for validation. Regarding the inter-comparability, it is found that parameters like the corrosion spot density or the penetration maximum on coated edges exhibit an average coefficient of variation of 62.6 % and 54.9 %. Better agreement is found for parameters like the total corroded area and the maximum edge corrosion penetration, with coefficients of variation of 14.3 % and 13.4 %, respectively. The developed methodology is further applied during a 68-month lasting outdoor exposure campaign of two types of solar reflectors at two representative sites, one exhibiting corrosivity class C2 and the other C3. On the commercial coating RL1, a total corroded area of 59 mm2 and 426 mm2 is measured after the outdoor exposure on the C2 and the C3 site, respectively, while on the novel low-lead coated reflector RL3 corresponding values are 280 mm2 and 1308 mm2. This shows the superior quality of the coating RL1 in terms of corrosion resistance. Furthermore, the analysis highlights the importance of proper edge sealing for corrosion protection, since corrosion penetration is increased by a factor between 1.3 and 4.0 if the edges are unprotected. The reflectance decrease after the outdoor exposure is regarded as negligible (0.000 - 0.005), thus not permitting any of the conclusions that are made from the novel image analysis technique.
- Enhancing Corrosion Resistance of Al-Mg Alloys through Biomineralization [Resumo]Publication . Marques, Maria João; Fori, Benoit; Mercier, Dimitri; Seyeux, Antoine; Zanna, Sandrine; Marcus, Philippe; BASSEGUY, RegineABSTRACT: In recent decades, new emerging microbiological technologies have been studied, based on the recognition that microorganisms can inhibit corrosion by different mechanisms, the so-called MICI (microbiologically influenced corrosion inhibition), opening up different lines of research. In this context, biomineralization has been attracting the attention of researchers, with an increasing number of studies showing that different types of mineralized layers formed on metal surfaces can reduce the risk of corrosion.
- Exploring Marine Biomineralization on the Al-Mg Alloy as a Natural Process for In Situ LDH Growth to Improve Corrosion ResistancePublication . Marques, Maria João; Mercier, Dimitri; Seyeux, Antoine; Zanna, Sandrine; Tenailleau, Christophe; Duployer, Benjamin; Jeannin, Marc; Marcus, Philippe; Basséguy; BASSEGUY, RegineABSTRACT: This study provides a detailed characterization of the AA5083 aluminum alloy, surface, and interface over 6 months of immersion in seawater, employing techniques such as SEM/EDX, GIXRD, mu-Raman and XPS. The purpose was to evaluate the evolution of the biomineralization process that occurs on the Al-Mg alloy. By investigating the specific conditions that favor the in situ growth of layered double hydroxide (LDH) during seawater immersion as a result of biomineralization, this research provides insights into marine biomineralization, highlighting its potential as an innovative and sustainable strategy for corrosion protection.
- La biominéralisation comme bioinspiration pour le développement de solutions anti-corrosion [Resumo]Publication . BASSEGUY, Regine; Marques, Maria JoãoRÉSUMÉ: Dans le domaine de la corrosion, la nature se révèle être une source d’inspiration pour développer de nouveaux concepts de protection verts. En effet, il est largement reconnu que les micro-organismes sont capables non seulement d’accélérer la orrosion mais ils peuvent également l'inhiber et/ou protéger les matériaux qu’ils colonisent [1]. Ce constat a ainsi conduit à proposer des stratégies à base microbienne pour l'inhibition de la corrosion des métaux. En particulier, le processus de biominéralisation à la surface des matériaux, tels que les pierres, le béton et divers métaux, a récemment été considéré comme une nouvelle approche respectueuse de l'environnement pour produire des couches protectrices [2-3]. Jusqu’à peu, la majorité des publications concernaient les aciers, matériaux historiquement utilisés dans les infrastructures. Au cours des dernières années, de nouveaux matériaux tels que les alliages d'aluminium, sont apparus sur le marché comme des alternatives possibles. Dans le cas spécifique de l'alliage Al-Mg, souvent utilisé dans les applications marines, peu d'études ont évalué l'influence de la biominéralisation sur la corrosion [4-6]. L'objectif de cette présentation est de montrer, à travers deux études de cas, comment la précipitation minérale influencée par l’activité microbienne sur les matériaux métalliques peut être envisagée comme une nouvelle approche pour le développement de solutions anti-corrosion.
- New proton exchange membranes based on ionic liquid doped chitosanPublication . Naffati, Naima; Teixeira, Fatima; Teixeira, António Paulo Silva; Rangel, Carmen M.ABSTRACT: The development of new proton exchange membranes (PEM) for electrochemical devices have attracted researcher's attention in the pursuit for more sustainable and cost-effective technologies for clean energy production and conversion. In this work, new doped chitosan (CS) membranes were prepared by the casting method. Chitosan is an abundant, biodegradable and non-toxic material, and as a membrane, a sustainable and cheaper alternative to those perfluorinated and commonly used, such as Nafion. Three different ionic liquids were employed as dopants, ([EMIM][OTf], [EMIM][FSI] and [MIMH][HSO4]), in various concentrations and up to 50 wt% load. The new membranes were characterized by ATR-FTIR, thermogravimetry, using TGA and DSC techniques to assess their thermal properties, and by SEM, to analyse their surface morphology. Proton conduction properties of the new membranes were assessed by Electrochemical Impedance Spectroscopy (EIS). The new doped membranes showed an increase in the proton conduction compared with pristine chitosan membranes. The incorporation of ionic liquids into chitosan membranes improved their proton conductivity and thermal properties, with [EMIM][OTf] and [MIMH][HSO4] showing the most promising results. A 2-fold increment in the proton conduction was generally observed with the increase of the temperature from 30 to 60 degrees C. The best proton conductivity was found at 60 degrees C for the membrane doped with [EMIM][OTf], with a value of 47 mS.cm(-1).
- NEWS4CSP Project: New coatings approaches to protect metallic materials from heat transfer fluids [Poster]Publication . Cunha Diamantino, Teresa; Pedrosa, Fátima; Paiva Luís, Teresa; Ferreira da Silva, Eduardo; Gonçalves, Francisco; Monteiro, Renato; Cardoso, João
- Portugal Offshore Wind, Green Hydrogen, and Sustainable Fuels: Power-to-X PathwaysPublication . Simoes, Sofia; Portillo, Juan C. C.; Simões, Teresa; Estanqueiro, Ana; Catarino, Justina; Costa, Paula; Oliveira, Paula; Ribeiro Pinto, Paulo Jorge; Lopes, Fernando; Lopes, Tiago; Gano, António; Duarte de Castro Fontes, Maria MargaridaABSTRACT: Portugal has a vast coastal area and significant offshore wind resources. The country has set ambitious targets and designated specific areas for offshore wind development. Current national policies are actively encouraging investment in these projects. This report compiles the latest strategies for offshore wind and green hydrogen in Portugal. It introduces the Power-to-X (P2X) concept, explores potential offshore wind-based P2X business models, and outlines the key processes and technologies involved. It also maps potential consumers of green hydrogen, along with the associated supply chains for hydrogen and sustainable fuels. A techno-economic analysis was conducted to identify viable pathways for Portugal. This involved selecting one of the planned offshore wind zones and, based on its location and potential capacity, determining the optimal onshore site and scale for a hydrogen and sustainable fuels hub. The report presents a comparative evaluation of seven scenarios, offering valuable insights for both public and private sector stakeholders.
- Simulation of Surface Segregation in Nanoparticles of Pt-Pd AlloysPublication . Correia, Jose B.; Sá, AnaABSTRACT: Platinum (Pt) and palladium (Pd) are crucial in hydrogen energy technologies, especially in fuel cells, due to their high catalytic activity and chemical stability. Pt-Pd nanoparticles, produced through various methods, enhance catalytic performance based on their size, shape, and composition. These nanocatalysts excel in direct methanol fuel cells (DMFCs) and direct ethanol fuel cells (DEFCs) by promoting alcohol oxidation and reducing CO poisoning. Pt-Pd catalysts are also being explored for their oxygen reduction reaction (ORR) on the cathodic side of fuel cells, showing higher activity and stability than pure platinum. Molecular dynamics (MD) simulations have been conducted to understand the structural and surface energy effects of PdPt nanoparticles, revealing phase separation and chemical ordering, which are critical for optimizing these catalysts. Pd migration to the surface layer in Pt-Pd alloys minimizes the overall potential energy through the formation of Pd surface monolayers and Pt-Pd bonds, leading to a lower surface energy for intermediate compositions compared to that of the pure elements. The potential energy, calculated from MD simulations, increases with a decreasing particle size due to surface creation, indicating higher reactivity for smaller particles. A general contraction of the average distance to the nearest neighbour atoms was determined for the top surface layers within the nanoparticles. This research highlights the significant impact of Pd segregation on the structural and surface energy properties of Pt-Pd nanoparticles. The formation of Pd monolayers and the resulting core-shell structures influence the catalytic activity and stability of these nanoparticles, with smaller particles exhibiting higher surface energy and reactivity. These findings provide insights into the design and optimization of Pt-Pd nanocatalysts for various applications.
- Tetrahedrite Nanocomposites for High Performance ThermoelectricsPublication . Coelho, Rodrigo; Moço, Duarte; Sá, Ana; Luz, Paulo P. da; Neves, Filipe; Cerqueira, Maria de Fátima; Lopes, E.B.; Brito, Francisco; Mangelis, Panagiotis; Kyratsi, Theodora; Pereira Gonçalves, AntonioABSTRACT: Thermoelectric (TE) materials offer a promising solution to reduce green gas emissions, decrease energy consumption, and improve energy management due to their ability to directly convert heat into electricity and vice versa. Despite their potential, integrating new TE materials into bulk TE devices remains a challenge. To change this paradigm, the preparation of highly efficient tetrahedrite nanocomposites is proposed. Tetrahedrites were first prepared by solid state reaction, followed by the addition of MoS2 nanoparticles (NPs) and hot-pressing at 848 K with 56 MPa for a duration of 90 min to obtain nanocomposites. The materials were characterized by XRD, SEM-EDS, and Raman spectroscopy to evaluate the composites' matrix and NP distribution. To complement the results, lattice thermal conductivity and the weighted mobility were evaluated. The NPs' addition to the tetrahedrites resulted in an increase of 36% of the maximum figure of merit (zT) comparatively with the base material. This increase is explained by the reduction of the material's lattice thermal conductivity while maintaining its mobility. Such results highlight the potential of nanocomposites to contribute to the development of a new generation of TE devices based on more affordable and efficient materials.